Long-term precipitation has caused different levels of water seepage in the walls, floors or ceilings of many residents' homes. Some households on the first floor have accumulated water, and furniture has experienced various degrees of dampness and water soaking. Good furniture has been peeled, rusted, and moldy. It's a pity to leave it unsightly and throw it away. So how to solve these problems?

 

 

The sofa is not easy to be moldy.

 

Sofas are usually divided into leather sofas and fabric sofas. The leather sofa can be cleaned with mildew remover after dampness, and then coated with leather oil on the surface. Avoid drying during maintenance, which will make the leather brittle and lose its softness and beauty. Tell the reader a small way, when you buy chicken legs, there will be a layer of chicken oil, and applying it on the skin surface can also protect the skin surface.

 

        If the sofa is usually cleaned and there is no dust on the surface, it is easier to clean up. Once the dust and water form a solution, it will deeply erode the interior of the fabric. If the tide surface is not large, you can use the cleaning detergent or other cleaning Agent treatment, and then slowly dry with a hair dryer.

 

In general, furniture must pay attention to normal maintenance. Although maintenance is not an emergency, long-term maintenance can greatly reduce the rate of furniture erosion in emergency situations, thereby winning time for furniture repair.

 

At ordinary times, pay more attention to the circulation of indoor air to maintain the balance of dry and wet indoors. When the weather is humid, do not open the south window to avoid the entry of moisture. At the same time, clean up frequently to keep the furniture clean and tidy without damage. In this way, it not only extends the service life of furniture, but also contributes to low-carbon environmental protection.

 

Material determines the degree of mildew

 

General furniture can be divided into materials, generally divided into panel furniture, solid wood furniture and metal furniture. Panel furniture is generally edge-sealed and has a strong resistance to moisture. However, the joints of furniture are hygienic dead ends. If you do not pay attention to cleaning at ordinary times, once the moisture is absorbed, it will cause the protective layer to separate from the internal wood. When the moisture content of the wood is increased, it will expand and deform, and in serious cases, it will cause the surface board to crack. You can put the moisture-proof bag in the damp place to absorb moisture, and then use the air conditioner to dry the wet part. When using the air conditioner, be careful not to blow it directly, otherwise it will cause the skin to crack.

 

        When the solid wood furniture is wet, small water droplets will appear on the outer paint surface, and sporadic mildew spots will appear. When cleaning, you should first remove the mildew spots on the furniture with water or a mild detergent, and then use the dehumidification equipment (The air conditioner in your home is fine.) Blow the damp part gently. Be careful not to blow directly when dehumidifying. Remember not to worry, and you must remove the water slowly. Finally, wipe gently with cotton cloth or soft dry towel.

 

Wooden furniture must be "dried" and cannot be exposed to sunlight, otherwise the skin and internal gradient of the furniture will increase, thereby cracking the furniture and losing its use value. According to the editor of Jiuzheng Building Material Network, in the usual maintenance, the panel furniture should pay attention to the protective layer on the surface and try to protect it from falling off. The solid wood furniture can be painted with walnut oil every once in a while, so as to keep the furniture cells full and not easily invaded by water vapor.

 

        After the metal furniture is wet or soaked in water, you should first check the rust condition of the part where the paint peeled off. If the rust condition is not serious, you can use the toothbrush replaced with a rust inhibitor to gently clean the rust. If it is more serious, you can use sandpaper or grinding wheel to clean it. After the bright metal layer is exposed, wipe it with a dry cloth and then apply anti-rust paint. (Editor: Peter)

 

Beauty Equipment Hose

Pvc Spring Hose,Protective Cable Hose,Beauty Equipment Hose,50Mm Flexible Conduit

Changxing VACUFLEX Hose Technology Co., Ltd. , https://www.vacuflex-cn.com