For a long time. The design of the motor cold welding process is performed manually by the craftsman. This manual preparation process plagued the craftsman. Because of the large number of motor cold weldments. The craftsman should make the calculation of the precise length and the drawing of the unfolding shape. Especially for complex parts, it is difficult to accurately calculate the deployment length. Often due to inaccurate calculations. Causes the waste material to be wasted, even causes the workpiece to be scrapped. Some cold weldments. Technicians need to repeatedly analyze its craftsmanship and how to make full use of materials.

Computer-assisted process design of cold weldment, logical analysis, accurate calculation of its expansion size to draw out the shape of the workpiece. Creation process specification. You can avoid wasting material waste. Excellent than the process, verify product quality, improve the level of technology.

It is very difficult to realize the computer aided process design of cold weldment. Because cold welding is not a twisted part, nor a non-twisted part with strong regularity. Research and development of computer-aided process design as a preliminary attempt to explore the cold welding process of the motor 2 to create a concept of motor cold weldment, concrete, system, using the prototype method and the basic principle of a creation method.

The sample method is based on the group technology and classifies and encodes similar or slightly similar motor product parts. Combine all the shape features in the same part family into the main sample. For example, the main sample of the windshield composite of the cold weldment in the motor product.

However, various wind deflectors are not the same in actual motor products. The actual design of the workpiece is related to the following combination of conditions 1 Whether there is a slanted hole 0S If yes, what is the number of holes N, to whether it is equal to that there is no outside edge, 3 outside is equal to zero, that is, 03 whether the cylinder part exists, 401 is equal to 0 Whether or not 1 is equal to zero exists at the same time, different combinations of conditions, determine the different entity design artifacts.

When the cold welding process is created. As long as the main sample enters the design dimensions to generate the process body. The computer is based on process masters and characteristic process parameters. Analyze and calculate the unfolding shape of the workpiece to create a technological procedure.

The generatrix method is when the process parameters of the unfolded parts are transmitted. Automatic access to the process knowledge base. The process logic is automatically created using logic languages ​​for various process decisions.

3 Cold Weldment Process Specification Chuang Cheng Cold Weldment Process Specification Chuang Cheng Formed by the process of the main body shape and management Mathematical model of the bridge to expand the shape of the formation of the production process decision text data mixed output large modules.

The process main body generates a process main body by generating and managing a module to add a certain type of design to the main sample of a certain type or a certain family part. And responsible for the process of the main data and process parameters sent to the mathematical model entrance.

The mathematical buccal bridge calculation module is when the entrance to the mathematical model bridge receives data. Through mathematical calculation model. Calculate the part unfolding geometry and other parameters. And send this data to the bridge exit.

Unfolded pieces are trapped to generate cheek blocks when data is received from the bridge port. The part's spread shape is immediately generated. And send the data marked in the geometric position.

It is also responsible for transferring these parameters to the process decision module. Participate in part process planning decisions. Different parameters are transmitted to generate different deployment pieces. 1 The wind deflector is welded by block unfolding pieces. Its unfolding pieces dynamically generate different unfolding pieces with different parameters that have holes or no holes transmitted. 2 is an unfolded part with a wall hole, and 3 is a part without a wall hole.

It is the best process plan to determine how many pieces of unfolded pieces are welded into windshields. The computer judges according to the calculated logic and process parameters transmitted, and optimizes the number of appropriate blocks to four conclusions. The establishment of the motor cold weldment system can complete the generation of the unfolded part shape from the workpiece shape, and the accurate calculation of the unfolded part geometry size. As part of the optimization process specification, and the output of the process documentation. From the craftman's manual preparation of the cold welding process specification to the computer-aided process design. It can not only optimize the process and improve the technological level, but also can greatly improve the work efficiency of the craftsman. Craftsmen are freed from a lot of tedious work.

Editing Tong Xinmin Data Input Sample 1 Kuding Arts Upper Body Entrance Mathematical Model Process Decision Module Drift 4 Cold Weldment Process Process Creation, Series Function Frame Difficulty God Continuous Casting Method and Equipment It can make continuous casting pull speed From the current number of meters per minute, to a few meters per second. It adopts a kind of conduit to inject the molten metal into the continuous casting process which is constituted by the crystallizer 56 to move toward the outlet, cools into a cast strand under the action of the crystallizer cooling water, and automatically strips the strand to the exit of the crystallizer.

The invention has the characteristics of design rationalization and complete process, can cooperate with the continuous rolling mill unit, realize continuous casting and rolling continuous production, and can greatly increase production efficiency and product rate.

Stuck 3 without wall hole unfolded piece best craft plan.

The process decision module automatically accesses the process knowledge base when the code size and geometric parameters of the main part are transmitted and the process parameters are transmitted. The process parameters and the group process are dynamically determined by the data processing and logical decision making process specification of the part. For example, if there are holes in the windshield, different process rules will be determined.

The process parameters of the unfolded parts of the parts and components of the mixed-distribution output module and the development of the unfolded parts are formed into a standard process, and the cold welding process process creates a logic function box.

System operation development module generating module turbulence module, fir,

Some people call Door Stops as Door Buffers or Door Stoppers. Whatever glass, wooden or metal doors, they need door stoppers.
Shape: Round, Half-Round, Oval Half-Round, Cylindrical Shape and other ruleless shapes etc.
Finish available: Satin SS, Polished SS, PVD, Old Silver, Black, Powder Coated, Antique Brass, etc
Should you have any further demands, please feel free to contact us any time. And welcome for OEM products with detailed technical drawings.

Door Stops

Ss304 Door Stops,Ss316 Door Stops,Brass Door Stops,Zinc Alloy Door Stops

Greatwall Hardware International Limited , https://www.greatwall-hardware.com